> Illegal opcode INT
> Segment boundry exceeded INT
> Unknown HW INT; ISR= 
  A) Alter Mem: a_ssss:oooo_hh
  B) Beakpoint: b_ssss:oooo; Clear: bc; bc1, bc2
  C) Cpu Reg: cxx_hhhh; Display: c
  D) Display Mem: d_ssss:oooo_ll
  E) Execute Binary Download: e
  F) Fill Mem: f_ssss:oooo_llll_hh
  I) In Port: i_pppp
  J) Floppy Cmd: j_.._.. buffer @3000
  K) Hard Disk Cmd: k_.._.. buffer @4000
  M) Move Mem: m_ssss:oooo_dddd:oooo_llll
  O) Out Port: o_pppp_hhhh
  R) Read Dev: rf_ssss:oooo_tr_hd_se_nm; rh_ssss:oooo_dh_ch_cl_se_nm
  S) Single Step: s_llll
  T) Switch Terminal
  V) Verify Memory: v_ssss:oooo_dddd:oooo_llll
  W) Write Dev: wf_ssss:oooo_tr_hd_se_nm; wh_ssss:oooo_dh_ch_cl_se_nm
  X) eXecute Time: x1; x2_hh_mm
  Z) Z80 Debug Cmd: z0= reset z80; z1= awake z80
> Restart power-up sequence
> Loading from port: 
> Switching terminal...
> z80 debug cmd must be run under Diag Console
> CPU Power-up tests ... 
> PRESS ANY KEY TO INTERRUPT AUTO-BOOT
 This space intentionally left blank. 
> Boot failed, status: 
> No bootable device
> Booting from floppy ...
> Booting from hard disk ...
> Select [1] to boot from Hard Disk
         [2] to boot from Floppy Disk
         [3] to enter Debugger
  Monitor ROM-11J at 
  Monitor ROM-13J at 
  Map ram address at 
  Main ram address at 
  (J13) Expansion Card 1 memory at 
  (J14) Expansion Card 2 memory at 
  (8259) INT Controller at 
  (58167A) Calender-timer at 
  (8254) Diag port timer at 
  (8274) Serial (Diag) port at 
  (8255) Parallel port at 
  Main Memory parity at 
  (J13) Expansion Card 1 Memory parity at 
  (J14) Expansion Card 2 Memory parity at 
  Diag Port Jumper Configuration Block Incorrect. 
  SMTU Jumper Configuration Block Incorrect. 
  Diag port Jumper Configuration Block Incorrect. 
  188 Comm Board Jumper Configuration Block Incorrect. 
  Z80 port 1 interface at 
  188 Communications Interface at 
> System configuration:
   Memory size (KB)= 
> PRESS any key to ALTER default setting
What Port are you Downloading to (1 to 5) ? 
Select Baudrate to use.
The Primary boot did not load properly at location xxxx
Enter CR to continue
Switching output from port 0 to port 1
   80287 Math Processor.
   188 Communications Interface Card.
   No Response from 188 Communications Interface Card.
   Primary Hard Disk FAILED test.                     
)                                             
   Testing Hard Disk.
  SMTU failed ROM checksum test.
  SMTU failed Data Buss test.
  SMTU failed Address Buss test.
  SMTU failed RAM test.
  SMTU failed DMA test.
  SMTU failed INTERRUPT chip test.
  SMTU failed FLOPPY chip test.
  SMTU failed HARD DISK controller test.
  No response from SMTU Tape controller. 
  SMTU failed Real Time Clock test.
  SMTU failed Interrupt Line tests.
  SMTU failed Tape Controller Self test.
  SMTU failed General Error
  SMTU failed General Error
  SMTU failed General Error
  SMTU Received NMI during Powerup.
  No response from SMTU controller.
  SMTU failed error code 0.
Main Ram Data Bus failed, address 0000:
Map Ram Data Bus failed, address 0000:
Main Ram Adress Bus failed, address 0000:
Map Ram Adress Bus failed, address 0000:
Main Ram Bank failed, address 0000:
Map Ram Bank failed, address 0000:
> CPU Monitor Debugger  V2.2
 from V2.2a Created (yr/mn/dy) 870329
